Home¡¡¡¡Introduction¡¡¡¡Quality¡¡¡¡Products¡¡¡¡Supports¡¡¡¡Feedback¡¡¡¡Contacts¡¡¡¡Chinese
   
¡¡ ¡¡ Technique Support
¡¡
Use Heating Method to Install the Bearing
¡¡¡¡Required for the installation of bearings with the bearings installed power increase in size rapidly. Due to the requirements of the installation of power, the larger bearing is not easy to push into the shaft or bearing inside. Therefore, the bearing or bearing before installing needs heating.
A:Principle of Induction Heating
B£ºHeating Installation
C£ºHoisting Machinery
D£ºShould not use open flame heating bearings
Principle of Induction Heatin
¡¡¡¡Induction heater can be compared with the transformer, it is the working principle of a primary coil with more turns and a few turns of the secondary coil mounted on the same core. Input and output voltage ratio is equivalent to the ratio of coil turns, while the energy remains unchanged. Therefore, the secondary coil in the low-voltage under conditions of high current. As for MF Induction Heater, the bearing is a single-turn short-circuit secondary coil, at a relatively low AC voltage under the conditions of a large current, resulting from a lot of heat. Yoke heater itself and remains at room temperature. As a result of this heating method to the current sensor, it will be magnetic bearings. Important to ensure to degauss the bearings, so that it will not scrap metal magnetic in the process of operation. All MF induction heaters have automatic degaussing function.
Heating Installation
¡¡¡¡Temperature between bearings and bearing installation location depends on the level of fit and the bearing size. Normal circumstances, the bearing temperature is higher than the axis of temperature 80 to 90 ¡æ (144 to 162 ¨H) is sufficient for the installation. But must not be allowed to bearing heating temperature exceeds 125 ¡æ (257 ¨H), because when bearing material changes occur, resulting in changes in diameter or hardness. Local overheating must be avoided, in particular, can not use open flame heating bearings. Heating in the installation of bearings to wear clean protective gloves. Use of lifting (lifting) machinery can be easy to install. Along the axis will be pushed to the installation of bearings, and make the bearings intact, push firmly until the match. Mingfeng provides a set of heating devices, such as the induction heater and equipped with adjustable thermostat for electric heating plate, to meet all needs of the installation under normal circumstances.
Copyright£ºTaizhou Ming Feng Electric Equipment Factory Main Products£ºBearing Heater¡¢Induction Heater¡¢ Steel Wire Rope Press¡¡ ¡¡
Contact£ºMs.wang¡¡Sales Line£º086-523-86865033¡¡Fax£º086-523-86862098¡¡E-mail:[email protected]
Address: 158# Taibai Road, Tangwang Town, Taizhou City
Ö÷Õ¾Ö©Öë³ØÄ£°å£º 久久久久久久久国产 | 国内一级纶理片免费 | 超碰小说 | 播放一级片 | 久久精品视频播放 | 久久机热| 欧乱色国产精品兔费视频 | 成人中文字幕在线高清 | 国产大学生毛片一级高清 | 久久久国产99久久国产一 | 久久国产精品久久国产片 | 九九99靖品 | 免费久久久久 | 国产高清大尺度一区二区不卡 | 国产黄色片一级 | 国产观看在线 | 黄色片不卡 | 免费一级a毛片在线播放 | 国产精品久久免费视频 | 国产精品自产拍视频观看 | 成人欧美精品一区二区不卡 | 国产一国产a一级毛片 | 国产伦一区二区三区免费 | 国产片一级 | 成人黄激情免费视频 | 久久国产精品免费网站 | 国产精品视频大全 | 免费看一级片 | 国产精品毛片一区二区三区 | 久久澳门 | 国产精品视频免费视频 | 黄色三级网站免费 | 久久99精品久久只有精品 | 国产成人久久精品推最新 | 久久一区二区三区不卡 | 狠狠色丁香婷婷久久综合2021 | 久久99精品久久久久久牛牛影视 | 波多野结衣在线一区二区 | 久久久青青| 久久成年视频 | 国产精品欧美一区喷水 |